aluminum chips from metal processing machine

Shred aluminum shavings in preparation for briquetting

To shred long and tangled aluminum shavings in a controlled manner and prepare them optimally for subsequent briquetting and recycling.
Request the right shredder now

CNC machining often produces long, spiral-shaped, or fluffy aluminum chips. These can clump together into bulky masses and cannot always be fed directly and evenly into a briquetting press. Upstream shredding reduces the chips to a controlled size and prepares them for subsequent compaction.

WEIMA shredders process aluminum chips from turning, milling, drilling, and sawing into a more homogeneous material stream. This stream can then be compacted into compact aluminum briquettes using a WEIMA briquetting press. This creates a coordinated process chain from loose chips to recyclable briquettes.

Why should aluminum shavings be crushed before briquetting?

Long turning chips and tangled milling chips can make it difficult to feed a briquetting press evenly. The shredding process breaks up clumps of chips and reduces them to a specified size. This facilitates material transport and creates more consistent conditions for the subsequent briquetting process.

Whether pre-shredding is necessary depends on the shape of the chips, the amount of material, and the intended pressing system. Short, free-flowing chips can sometimes be briquetted directly. Long or woolly chips should generally be tested first in a material test.

A pile of aluminium shavings in one hand
Shredded Aluminum chips in hands with glove
Milling waste aluminum swarf
Maximum recovery, minimal effort. Request a shredder for aluminum chips now.

WEIMA Machines Suitable for Processing Aluminum Chips

From shredding long and tangled chips to compressing them into compact briquettes
Product image of the WEIMA WL 4 Single-shaft Shredder
Single-shaft shredder
WLK Series

The robust single-shaft shredders of the WLK series break up large clumps of chips and reduce long aluminum chips to a controlled size. This creates a uniform material flow for subsequent briquetting.

WEIMA ZM 50
Four-shaft shredder
ZM Series

The low-speed, four-shaft shredders in the ZM Series are particularly well-suited for long, bulky, and heavily tangled aluminum chips. Two cutting shafts and two feed shafts powerfully draw in the material and reliably shred it. This makes the ZM Series a compact solution for chips that are difficult to feed.

Product image of the WEIMA TH 700 M briquette press
Briquette Presses
TH Industrial Series

The TH Industrie Series briquetting presses compress shredded aluminum shavings into compact, dimensionally stable briquettes. This reduces volume, facilitates storage and transport, and prepares the material for recycling.

0

Shredding and Briquetting Aluminum Chips in Practice

From loose wood chips to compact briquettes
thyssenkrupp Automotive Body Solutions: Aluminum Chip Shredding and Briquetting with WEIMA

The aluminum scrap from lathes and milling machines is shredded using a WEIMA WLK 4 single-shaft shredder and then compressed into highly compacted briquettes with a diameter of 60 mm using a WEIMA TH 600 M briquetting press.

Shredding and Briquetting Aluminum Chips Using a WEIMA WMS 60 & TH 1500 M

The WEIMA WMS 60 reliably shreds aluminum chips and prepares them for subsequent briquetting with the TH 1500 M. This optimized process chain reduces the volume of material and enables efficient further processing and recycling of the aluminum.

0
Ready for your process solution? We'll configure the right shredding and briquetting solution for your material flow.

Briquetting Crushed Aluminum Chips

After shredding, the aluminum chips can be compacted into dense, dimensionally stable briquettes using a WEIMA briquetting press. The high pressing force significantly reduces the volume of the loose chips, thereby facilitating storage, transportation, and further processing.

During the briquetting process, cooling lubricants and emulsions can be separated from the material, collected, and reused if necessary. The resulting aluminum briquettes can be handled more efficiently and prepared for subsequent melting in the recycling process.

A mountain of silver aluminium briquettes from the TH 1500

The Aluminum Recycling Cycle

From aluminum shavings to the new final product
Employee holding bulky piece of aluminum turning scrap
1. Collect aluminum shavings

Machining aluminum produces long, spiral-shaped, and tangled chips. These are collected and set aside for further processing.

A WEIMA shredder that shreds aluminum chips, preparing them for briquetting
2. Shred aluminum shavings

WEIMA shredders reduce the size of bulky aluminum chips and ensure a more uniform chip structure. This optimally prepares the material for subsequent briquetting.

Aluminum shavings that have been compressed into rectangular briquettes and can now be recycled
3. Briquetting aluminum shavings

WEIMA briquetting presses compress the shredded chips into compact, dimensionally stable aluminum briquettes. This significantly reduces the volume of the material, and any cooling lubricants it contains can be recovered.

Melting process of aluminum
4. Melt aluminum briquettes

The compacted aluminum briquettes are fed into the recycling process and melted down. This allows the aluminum to be reused as a valuable secondary raw material.

Aluminum cylinder turning process chip
5. Manufacture new aluminum products

The recycled aluminum is used to make new products such as profiles, components, and other semi-finished goods. During the further processing of these products, aluminum shavings are generated again, which can be crushed and briquetted—thus closing the material cycle.

0

Frequently Asked Questions About Shredding and Briquetting Aluminum Chips

Concise answers on processes, machine selection, and recycling.

Long, spiral-shaped, or tangled aluminum chips can make it difficult to feed a briquetting press evenly. Shredding breaks up tangled chips and creates a more controllable material flow for the subsequent briquetting process.

No. Whether pre-shredding is necessary depends on the shape of the chips, the amount of material, moisture content, and the briquetting press. Short, evenly flowing chips can sometimes be briquetted directly. Long or heavily tangled chips should be shredded first and, ideally, evaluated through a material test.

WEIMA shredders can process, among other things, turning, milling, drilling, and sawing chips from aluminum machining. Shredding is an important preparatory step for subsequent processes, especially when dealing with long, spiral-shaped, or woolly chips. The specific machine configuration depends on the chip shape, quantity, and desired final size.

After shredding, the aluminum chips are fed into a briquetting press either continuously or in batches. The machines in the TH Industrie series use hydraulic pressure to compact the material in a die, forming dimensionally stable aluminum briquettes. No binders or adhesives are required for this process.

Briquetting reduces the volume of loose wood chips and facilitates storage, handling, and transport. Compact aluminum briquettes can be processed in a more controlled manner and sent for metal recycling. The actual volume reduction achievable and the quality of the briquettes depend on the raw material and the machine configuration.

Yes, when working with damp aluminum chips, cooling lubricants, residual oils, or emulsions may leak out during the pressing process and can be collected using the appropriate equipment. Whether and to what extent recycling is possible depends on the liquid, the material, and the operational cycle.

Yes. At the WEIMA Technical Center, aluminum chips can be shredded and briquetted under real-world conditions. The material test helps determine the appropriate machine type, cutting configuration, screen size, and briquetting solution for the specific application.

A scene showing a WEIMA employee speaking with a customer, with several WEIMA machines visible in the background.
See for yourself Shred and briquette your material now using our machines.
Newsletter
Sign-up for our newsletter today.
Sign-up for our newsletter
Sign Up